Garage Door Repair

Garage Door Won’t Open All the Way? 8 Things to Check

Garage Door Won't Open All the Way

You were just about to leave the house when you noticed a problem in the garage – your garage door won’t open all the way!

This problem can be particularly frustrating because it’s not always clear if the problem is something minor you can resolve quickly or something major that requires a trained professional. There are a few things you should check before picking up the phone.

Here’s a step-by-step guide to help you troubleshoot the problem.

Garage Door Won’t Open All the Way (Troubleshooting Checklist)

This checklist will help you identify the reason why your garage door won’t open all the way, which in turn will reveal whether or not it’s time to call in a professional garage door repair service.

  1. Close the door
  2. Unplug the garage door opener
  3. Disengage the garage door
  4. Test the door manually
  5. Secure the door if necessary
  6. Check the tracks
  7. Check the rollers
  8. Check the limit switch

Let’s take a closer look …

1. Close the door completely

In order to figure out why your garage door won’t open all the way, you first need to make sure it’s secure.

You don’t want the door to come crashing down on you or anyone else, once you begin disengaging your garage door opener.

If you can, close it completely to ground level.

2. Unplug the garage door opener unit

You may not have even noticed it before, but the main garage door opener unit will be plugged into an electrical outlet that is located on the garage ceiling near the unit.

Using a ladder to reach the unit, unplug the cord from the outlet.

3. Disengage the garage door

You will want to disengage the emergency release for the door. It is usually hanging from the center rail that the opener sits on, close to the garage door.

Often, it is red and is marked. You may also need your ladder to reach it.

Pull the lever down – you’ll feel the spring-loaded lever disconnect, and it will stay down.

4. Test the door manually

Now that the opener is offline, try moving the door up and down yourself.

If it seems to be operating smoothly with just human power, the problem is with the garage door opener itself.

5. Secure the door if necessary

If it has stopped and stuck fairly high up on the tracks – enough to cause a problem if it suddenly comes down – you’ll want to prevent it from dropping.

Use C-Clamps tightened onto the tracks just below the bottom of the garage door, or insert a 2×4 or similar piece of sturdy lumber below the door.

6. The tracks

The tracks are the metal guides at each end of the garage door.

The door itself moves on rollers along these tracks as it opens and closes.

It’s possible that the tracks themselves have gotten debris or dirt in them, which is preventing the rollers from moving. Since you know how far up the door is rising, start your search from that point. Look for gravel, pieces of wood, or other things that could stop a roller – and remove them. You’ll want to use your ladder to help you examine the upper parts of the track. If your tracks are dirty, clean and lubricate them.

The tracks themselves may have become bent or uneven – this can happen when there is an issue with the pulleys, or the torsion springs need adjustment. The misalignment issue is one that that will need to be addressed by a professional.

7. The rollers

These are the wheels that roll along the tracks, making your garage door easy to operate – when they’re working right.

Like any other parts, they can also become damaged or rusty. Check each one for rust or damage – you may need to have one or more rollers replaced.

It’s also possible that they have become sticky and need to be lubricated. If you take care of this problem yourself, be sure to use a lithium-based grease or a product that is labeled for use on garage doors. Spray it inside each roller so that the bearings inside are treated.

Do not spray lubricants on nylon rollers, if you have them.

8. The limit switch

If everything is working with your garage door when operated by hand, the problem lies somewhere within the process that your garage door opener utilizes.

This switch tells the garage door opener when to stop – and if the adjustment is wrong, it can cause your unit to continually stop at the same (wrong) point every time it opens.

If you think this is the problem, you’ll need to mark off the point that it opens to, and then measure the distance between the bottom of the garage door and the ground. This will give you the amount of adjustment needed in the unit.

The adjustments can be made by turning the screws on the garage door opener unit near the motor. You can refer to your owner’s manual for their location. This can be a tricky and frustrating process, as you must keep setting and testing the adjustment to see if your door is working properly. It may well be worth your sanity to call a professional to deal with this issue.

If there are no obvious reasons for your garage door opener to give up partway through lifting your door, you likely have a failure somewhere within the unit and will need a professional to evaluate the problem, and/or replace the entire unit.

Keep everything secure

If you must wait for a repair, don’t forget to lock your garage door for security.

Normally, your garage door opener takes care of this for you, by keeping the door pushed down to the bottom of the garage floor. If you have disconnected the opener, locate your garage door lock. If you have one, it will be operated with either a slide bar or a T-handle mechanism.

The slide bar can be secured with a padlock, and the T-handle style is locked with a key. Slide bars are located inside the garage door, and T-handle locks are located on the outside of the door.

Be sure to unlock the door before you try to use the door again, and don’t misplace the key in the interim.


Using this troubleshooting checklist will help you identify why your garage door won’t open all the way. Once you’ve identified the problem, you will know whether or not it’s time to call in a professional.

Garage doors involve a number of moving parts and require regular maintenance in order to function properly for the full lifespan of the door. Please let us know if you have any questions or if you need help fixing your door.

Garage Door Repair

How to Fix a Dented Garage Door

Garage doors may become dented for a variety of reasons, including everything from weather to vehicle accidents.

No matter how it happens, a garage door dent will impact the appearance and functionality of your garage door. For this reason, it’s best to seek the help of a professional who can perform the garage door repair you need to get your garage door back up and running.

In this article, you will learn how to fix a dented garage door.

How To Fix a Dented Garage Door

No matter how well you take care of your garage door, eventually you’re going to be dealing with dents. They happen for all sorts of reasons, and often you just can’t prevent them. If you’ve found a dent in your garage door, don’t panic.

You may be able to repair minor damage and restore the original appearance of your garage door. Here’s how to fix a dented garage door.

Here’s how to fix a dented garage door.

How Garage Door Dents Happen

There are all kinds of reasons why you may be dealing with a dent in your garage door. You could have suffered a particularly bad storm, and hailstones or even a falling tree branch may have dented your door. Perhaps your kids accidentally kicked a ball into the door, denting it. You may have even driven your car into the door while you were having an off day. No matter how careful you are, it’s very easy to accidentally dent it.

DIY vs. Professional Repair

You have two options when it comes to mending dents in your garage door. You can call in an expert to mend it for you, or you can mend it yourself. There are advantages to both.

If you mend your garage door yourself:

  • You can get the dent fixed right away.
  • You’ll save some money as you won’t need to pay someone for their time and expertise.
  • If you’re handy it won’t take you very long.

If you call in an expert:

  • You won’t have to worry about causing more damage to your garage door.
  • The expert will get the job done quickly and cleanly.
  • They’ll be able to inspect your door and ensure it’s working properly before they go.

There are good reasons to try both methods, so it’s very much up to you. If you’re feeling confident, you can try and repair your garage door yourself. If you’re not, you can easily call in a professional.

Mending Your Door ASAP

It’s important to repair those dents in your garage door as soon as you can. Firstly, those dents can look unsightly even though the damage is just cosmetic. If you’re looking to sell your home, those dents can have a seriously detrimental effect on your curb appeal.

It’s also important to repair the dents as they can cause damage to the door over time. If left unchecked, they could affect the way the door opens, leading to more costly repairs in the future.

How To Fix That Dent

Now if you’re going to DIY your repair, you’ve got a lot of options. There are a few different repair methods out there, so here are some that you can try.

Hammering Out The Dent: This is the most common way of repairing a dent, and it’s the first method you should try. You’ll need a square piece of wood and a hammer. Hold the wood up against the distending side of the dent, and hammer against it to tap the dent out. In most cases, this will be enough to mend it.

Using A Lighter And Compressed Air: This method sounds difficult, but it’s honestly quite simple and effective. To start, you’ll need to clean the area thoroughly with some dish soap and water and allow the area to dry completely. Next, you’ll need some aluminum foil, a lighter, and a can of compressed air. Roll out the foil across the dent, and hold it there as you run a lighter across the dent for a minute. Once you’ve done that, remove the foil and then spray the compressed air at the spot for about 30 seconds, keeping the can upside down the entire time.

The change in temperature from hot to cold should pop that dent right out, meaning you won’t have to do any more work on it.

Suction Cup Method: This method is often used by auto body shops, and it’ll also work on your garage door. All you do is attach a suction cup to the dented spot in the door, and pull it out using the cup. Head to a hardware store or auto body shop to get a suction cup that will work on your door.

Filling In The Dent: This method is often used if you’ve tried the above tricks, and you haven’t totally got the dent out. It’s still quite simple so it’s a DIY job you can do over a weekend.

You’ll need to sand down the indented area, and mix up some auto body hardener according to the instructions on the packet. Then, apply the filler to the area, smoothing out the dent. Allow it to dry again according to instructions, and then sand it down to smooth it. You’ll then need to prime the spot and paint the garage door in order to blend the filler in with the rest of the door.

What If It Doesn’t Work?

If you’ve tried to fix your own garage door and found that the dent still won’t come out, don’t despair. Sometimes the dents are just not going to come out with conventional methods. When you’ve tried yourself and you can’t get the dent out, you should call in a professional team to come and look at the door for you.

They’ll have more tools and experience at their disposal, so they may have some ideas on getting that dent out. In most cases, you’ll get a free quote so you should certainly take advantage of this.

In most cases, they’ll be able to mend the dent themselves, ensuring your garage door will look great again. Sometimes, you’ll find that you’re going to need to replace your garage door. This happens when the dent is too large or complicated to mend. Your garage door professional will let you know what is happening with your door, and what your options are.

Mend That Dent Today

Now you have all the information at hand, you can ensure that your dent will be fixed as soon as possible. It’s a lot easier than many homeowners imagine, so it’s worth trying to fix it yourself. Give it a try today.

Garage Door Repair

How To Repair A Broken Garage Door Spring

When it comes to your garage door, the most common issue you’ll get is a broken garage door spring. This can affect the opening mechanism of your garage door, so how do you get it fixed quickly and efficiently?

In this article, you will learn how to repair a broken garage door spring so you can fix the problem quickly and safely.

How to Repair a Broken Garage Door Spring

The springs in your garage door system play a major role in the operation of your garage door.

Should your springs fall into disrepair, they could cause a major problem for your garage door, your personal safety, and your property. For this reason, we recommend keeping a close eye on your garage door as a way to identify potential problems.

If you find your garage door is operating strangely or making unfamiliar noises during operation, your door may need service and repair. There are several things to consider before repairing a spring, which we’ll go over in detail below.

Here’s how to repair a broken garage door spring.

Why Springs Need Repair

Your garage door springs are probably the hardest working part of your door.

They’re working every day to open and close the door, and so they will wear out over time. They work by stretching and uncoiling and then coiling back up again, over and over again. As you can imagine, this creates tension in the spring and can eventually wear it down.

A Note About Garage Door Springs And Safety

Any good homeowner should know that they need to keep maintaining their garage door, to ensure it’s working at top capacity. You also need to keep an eye on your garage door, as a broken garage door spring can put you in a lot of danger. As you keep using that spring, it will get more and more worn out. You want to ensure that you replace it before it breaks entirely, as this could result in personal injury and property damage.

Which Type Of Spring Do You Have?

To replace a garage door spring, you first need to know what kind of spring you have. There are two main types that you may have, so which one do you have?

Torsion springs: These are the most common styles of springs that are found in garage doors. They’re tightly wound coils of metal, that give your door the torque it needs in order to open. You can have up to four springs on the door, depending on how heavy it is.

There are several different styles of torque spring, so you’ll need to know which kind it is that you have. As a homeowner, you’re most likely to have standard torque springs on your door. These are usually mounted at the top of the door and have a metal shaft running through them to support the spring.

Extension springs: These springs are the ones you’ll most commonly see in residential homes, so you’re more likely to have an extension spring on your door. These work by expanding and contracting, as the name implies, to open your door. These are the springs that are likely to be volatile when they break, so you need to meticulous about replacing them before they get to that point.

These springs should always come with a safety cable, to ensure that they’re fully supported and safer to use.

How To Tell When The Spring Needs Repair

So, how can you know that the springs on your garage door need to be replaced? Here’s what you need to be looking for.

Torsion springs: It’s quite simple to test these springs and check they’re still in good shape. Disengage your automatic door opener and open the door fully. You’re checking to see if the door can hold its weight on its own. If the door stays open, then your springs are still in good condition. If the door starts to close, then they need to be replaced.

You can also open the door halfway, to see if the door can stay open like that on its own. If it can’t, you’ll need to get those springs replaced.

Extension springs: Signs of wear are similar to those in torsion springs, so you can conduct similar tests on your garage door. There are some additional checks you can make, too. For example, take a look at the springs and see if there are any gaps in the spring. If there are, this is a sign that it can’t produce enough tension to open the door anymore.

You’ll also want to take a look at the garage door itself. Are the left and right sides of the door not properly aligned? A spring may be on its way out. Look for general wear and tear on the springs too, to see if they need to be replaced.

Replacing Your Springs

If you feel that the springs need to be replaced on your garage door, then the best thing to do is call in a garage door repair company to come and handle it for you. As detailed earlier, a worn out spring poses a real danger to you and your family. Even those that are experienced in DIY can be in danger if they attempt to change the spring out themselves. It’s much safer to call in an expert to handle to change over for you.

When you call a repair company to handle the spring, they’ll come out and examine it for you, to ensure that it’s the spring that is the problem. They’ll also check the workings of the rest of the door, to make sure there are no other problems that you need to be aware of.

Once they’ve done this, they’ll go over what needs to be done with you, and agree on a price with you. They’ll usually sign a contract with you, to ensure that you both know what you should be paying, and what exactly should be being done to your garage door.

They’ll get to work, and usually within a day, they’ll be able to get that spring fixed for you. Having a fixed spring means that you won’t have to worry about your door being unsafe, and it’ll be working properly for a long time after the repairs.

Fixing your garage door springs is an important job that shouldn’t be neglected. Keep an eye on your springs, and ensure that you get them replaced when needed.

Garage Door Repair

How to Fix A Garage Door Off Track (And 6 Reasons Rollers Derail)

Garage doors are made functional by a system of rollers, tracks, and switches. It takes quite a bit of force to raise and lower such a heavy door so frequently. Garage doors also receive quite a bit of use, day in and day out. So it’s understandable when things go wrong, like when the door itself comes off the tracks.

The best way to address any problems with your garage door is to consult a garage door professional for their assistance. They can assess the problem and either make suggestions or repairs to help the door run more smoothly. They can also advise you as to whether you should replace your garage door entirely.

However, a garage door coming off the tracks is a common problem that the homeowner can fix his or herself with a bit of instruction. Further, understanding why rollers derail can help you prevent this problem from occurring in the first place. If you’re facing a garage door dilemma, consider the following steps to solving that problem.

Here’s how to fix garage door off track.

How to Fix Garage Door Off Track

If you’ve noticed your garage door off track, we have some tips to help you understand how to fix garage door off track:

  1. Gather materials needed for putting a garage door back on its tracks. These include a wrench, hammer, pliers, wood blocks or sawhorses, and some sort of lubricating substance like spray or even cooking oil.
  2. Get someone to help you open the door manually after disconnecting it from the opening mechanism. Your helper should help you lift the door and then set it on saw horses or wood blocks to keep it open.
  3. As you open the door, pay attention to where the door catches on the tracks so you know where it’s coming off track.
  4. Apply grips or locking pliers to help keep the door up, in addition to having the sawhorses or wood blocks there for safety reasons.
  5. Using pliers, manipulate the metal on the edge of the track and slip the wheels back into the track. You can secure the wheels into the track by knocking the edge of the track back into shape as it was before you used pliers on it.
  6. Make sure the door is reattached to the opener and can open and close smoothly.

In order to fully understand how to fix garage door off track, it’s best to refer to your owner’s manual. If you’re not comfortable troubleshooting your garage door, please feel free to contact Your Garage Door Guys for assistance.

Six Common Reasons Rollers Derail

Pinpointing reasons that garage door rollers derail and working to prevent those causes is the best way to keep your garage door running smoothly and safely. Keep the following causes of rollers derailing in mind when inspecting your garage door regularly:

  1. Not enough lubrication: A main reason garage door rollers derail is that the track and the rollers themselves are not lubricated properly. These two surfaces will generate a lot of friction, so it’s important that they have the lubrication needed to keep moving together smoothly. Sprays like WD-40, silicone oil, or even household cooking oil will suffice to create enough lubrication to keep the rollers moving smoothly along the track.
  2. Tracks aren’t secured properly: If you or the person who installed your garage door didn’t install it securely, you may end up having problems with your garage door tracks later down the line. Tracks that are not securely fastened to the garage wall can create problems by moving too much, coming off the wall entirely, or just being slightly loose enough to misdirect the rollers. So, it’s important to make sure your tracks are firmly and tightly fastened to your garage walls.
  3. A misaligned track: Similar to poorly secured tracks, those that are misaligned can also cause problems. Misalignment problems can be easily fixed by loosening fasteners and adjusted the track as needed and then securing the tracks again.
  4. Dirt is causing problems: Garages are dirty, dusty places, and this dirt and dust can get into your garage door track causing roller problems. If there’s dirt in the roller track and there’s not enough lubrication, this is enough to jam your rollers and send them right off the tracks. You can fix this problem yourself with a strong dish detergent and scrub brush. Just remember to re-lubricate the tracks when you’re finished.
  5. Damaged tracks: Garages can also be risky places where your tracks may be damaged for one reason or another. Cars backing into tracks or other blunt forces can bend or dent them, sending rollers off the rack or jamming them. Aside from being careful, knocking these dents out is possible with a rubber mallet.

Of course, the best way to keep your garage door running smoothly is to ensure it receives routine maintenance from professionals who are trained to identify and address problems, whether they be easy to spot or more difficult to notice. Be sure to schedule a regular inspection of your garage door by either a garage door professional or a landscaping expert–either one.


Repairing a garage door doesn’t have to be a headache or an ordeal. It’s actually quite simple when directions are followed and safety precautions are taken. The most important step is to have a professional regularly inspect the garage door. Garage door tracks can easily be repaired by moving the door manually and then securing it with pliers or sawhorses while you watched. And make sure your tracks are secured to your walls; this will also ensure that the tracks stay completely still. Doing so will ensure a safe and working garage door for your home.

Ensuring that your garage door rollers are in good shape and won’t become derailed is a priority, and homeowners can do that by paying attention. To prevent rollers from coming off the tracks, make sure the tracks are clean and have enough lubricant. Misaligned tracks can be identified easily, and luckily, their fix is simple and straightforward.

Garage Door Repair

Homeowner’s Guide to Garage Door Spring Repair

Looking for help with garage door spring repair?

Garage doors use a spring system to counterbalance each side of the door so that it lifts evenly.

If the spring breaks, your garage door won’t open or close as designed. This can become a major headache when you need to be somewhere and can’t get your car out of the garage.

This guide will provide an overview of the different types of garage door springs and what garage door spring repair requires.

Here we go!

What are the garage door springs?

Springs make it easier to open and close your garage door. Without them garage doors would be extremely difficult to use; for most people, it would be impossible because they are so large and heavy.

Residential garage doors are equipped with one of two types of springs: extension or torsion.

Torsion Springs

Torsion springs are located above the door. They’re mounted on a metal rod parallel to the door. Pulleys attached to the bottom of that metal rod connected to the bottom of the door via cables.

When the door closes the pulley turns the rod to create tension in the spring. Opening the door releases that tension by unwinding the spring.

Torsion springs are usually guaranteed for three to seven years, or 30,000 times of opening and closing.

Extension Springs

Extension springs are mounted above the door’s horizontal tracks and run perpendicular to the door. They’re not mounted to a rod, rather, they’re suspended between two brackets. The length of the springs depending on how tall the door is.

When the door opens, the springs contract and tension are released causing the door to lift.

These springs are typically a lighter-gauge metal than torsion springs.

Why Garage Door Springs Fail

General wear-and-tear is the biggest reason springs fail. Your garage door is one of the most frequently used doors of the home. Because of this, its components are put under a lot of stress; eventually, the springs lose their capacity to compress and expand.

Added weight reduces the lifespan of garage door springs by placing extra stress on them. Things like windows and even paint can add weight to the door. Look for things like uneven gaps between the rings of the spring, bends, or excessive looseness; these are all signs that your spring is faulty.

Well-maintained springs can last up to thirty years. But lack of maintenance will contribute to their early failure. They need to be regularly inspected for things like loose tracks, damaged hinges and bearings, cracked springs, and adequate lubrication. Proper lubrication prevents rust that weakens the springs causing them to break.

Maintenance to the safety cable in extension springs is especially important. The safety cable keeps the spring from exploding pieces of metal in all directions. The cable should be smooth and free of frays.

What Can Go Wrong With Springs?

There are a variety of reasons that may cause garage door springs to fall into disrepair. In our experience, the following are the most common reasons.

Springs can become out of balance

Normally, garage doors can be opened with one hand from the middle of the door. The door opens smoothly. If you notice the door pulling on one side or won’t stay open where you want it then the springs are probably imbalanced. These can typically be adjusted rather than having to be replaced.

They’re too tight

When the springs are too tight you may notice that the door flies open. If you’ve got a garage door opener you may not notice it immediately, but the damage is still occurring. The electric gears of the opener have to work harder when the springs are tight which causes more wear and tear on the machine.

Springs are squeaky

Noisy springs may be disconcerting, and annoying, but they aren’t necessarily a sign of trouble. Before worrying, try using a spray-on lubricant to see if that resolves the issue.

There’s a problem with the brackets

Sometimes the problem with the door isn’t the spring, but the brackets at the bottom of the door. These, like the springs, are under a lot of pressure and should be adjusted with great care. Most newer models are tamper-resistant and can’t be accessed without a specialized too.

A Few Words of Caution

These springs can be very dangerous because they’re held under tension that holds a great deal of energy. Energy is released when the spring suddenly unwinds after a break or if it’s been improperly handled. Physical harm results regardless of how the tension is released.

For extension springs, make sure you have a safety cable installed to prevent the spring from flying apart if it does break. A safety cable is comprised of metal cording anchored to the wall or ceiling that runs through the garage door spring.

Before working on either type of spring ensure that all tension is released. It’s dangerous to work on a spring that is under pressure because that energy can be released quite violently, causing significant bodily harm.

Do It Yourself or Call A Professional?

If you have some do-it-yourself home improvement experience, you may be able to perform the garage door spring repair needed to fix your garage.

With that said, it’s a pretty big project so you may want to call in a garage door repair professional for help.

A professional will know exactly what parts are needed to repair your garage door spring, so you can rest assured you won’t have to spend a lot of time researching the available parts. In addition, a professional will be able to check for other potential problems while performing the repair.


Springs are an integral part of the garage door; without them, the door wouldn’t open properly.

Like other heavily used components, the springs can fail, sometimes without warning. Before undertaking repairs it’s a good idea to understand how the springs work, what to look for when they malfunction and acknowledge and implement some safety tips.

Garage Door Repair

How to Replace Garage Door Torsion Springs

A broken torsion spring is one of the most common garage door problems.

The torsion spring is located horizontally above your garage door and provides the tension needed to lift your garage door. If the spring breaks, it won’t have the tension needed to open and close your garage door. In some cases, you may notice your garage door lifting partially.

Either way, it’s important you’re able to identify this problem so you can resolve it quickly.

This guide will help you understand how to replace garage door torsion springs so you can decide whether to fix the problem yourself or call in a professional garage door repair professional.

Let’s get started …

How to Replace Garage Door Torsion Springs

Replacing garage door torsion springs can be a complicated process, even for the most experienced do-it-yourself homeowner. If you’re not comfortable with the project, it may be in your best interest to contact a professional garage door repair provider in your area.

Garage door torsion springs are available online or occasionally at brick and mortar stores. This is a rather complicated project that can be done by an experienced do-it-yourself person if one follows the correct safety precautions. We’ll go over the steps to replacing a broken torsion spring, look at the hazards, and educate you on how to either go ahead with the project or decide if you’d rather leave this task to a professional.

Here’s how to replace garage door torsion springs.

1. Begin Removing the Old Springs by Securing the Door to the Track

If your door has two springs, which many do, it is wise to replace both of them at the same time.

Close the garage door and use C-clamps to hold the door closed. Do this by attaching the clamp to the garage door track just above the door roller at the very bottom, on each side of the door.

Now, unplug the garage door opener, if you have one, and disengage it by pulling the cord on the unit’s arm.

2. Check Your Safety Equipment and Procedures

You’ll want to have the following safety equipment and adhere to the following precautions: Wear eye protection and leather work gloves.

Use ONLY a set of professional quality winding bars to wind or unwind the spring. These are available online. Do NOT grab the spring or cones. NEVER position yourself in front of the spring cones while you are adjusting them – work to the side. And always use proper ladder safety procedures.

Broken garage door springs are a leading cause of injury in the U.S.

3. Ensure that Your Old Spring Matches the Replacement

You’ll want to make sure that the type and dimensions are the same.

Measure the old springs to determine the wire gauge, diameter, length, and wind. Now is the time to also mark the location of the drums and torsion shaft while they are in place.

This will help you balance them correctly. Again, do not touch the cable drums or grab the shaft.

4. Unwind the Old Springs

Use only winding bars for this step. Insert the winding bar in the bottom hole of the cone.

You must hold the bar in position and then loosen the two setscrews. Be prepared to hold on tightly, as the pressure will release in a powerful way. Do not remove the winding bar at any time during this step! Now, insert the second winding bar in the next hole. Remove the first bar and let the spring unwind one quarter turn each time.

You’ll need to ‘leapfrog” the bars as you move from one hole to the next.

Remove the center bracket holding the torsion rod by unscrewing the bolts, (put them in a safe place), and slide off the old springs. Use another C-clamp or locking pliers to secure the tube to the center bracket, so that it doesn’t fall off and cause an injury.

5. Install Your New Springs

For this example, we’ll start on the left. Install the first spring by sliding it onto the torsion rod, from the center.

Slide on the cable drum next. The cone on the end of the new spring should be pointing to the right and the center. After you’ve relocated the spring, and reattached the cable drum, replace the torsion rod into its bracket on the left.

6. Replace the Center Bearing

Push the rod to the left, to the outside of the garage door, and slide on the center bearing from the inside of the bar. Now, add the right spring by sliding it onto the bar from the center. Insert the center bearing into the right cone.

You’ll need to bolt the cones to the center bracket, using the same hardware. Remove the C-clamp or locking pliers.

7. Thread the Lift Cables

Pull the lift cables in a straight line between the door rollers and the garage door frame.

Reattach the cable stop at the end through the slot on the drum on the end of the torsion rod. Now, use your clamp or pliers on the rod to hold it stationary as you tighten the drums. Rotate the drum slowly to wind the cable tightly and correctly, and tighten the set screws. Repeat this on both sides of the door, making sure the torsion rod stays in place and cannot rotate.

The two sides of the door must have equal tension on the cables to work properly.

8. Rewind the New Springs

Using the two winding bars, you will now begin to tighten the spring with the winding cone, using the same process you did to loosen them.

Alternate the position of the two bars in the holes, and tighten one quarter turn each time. Follow the manufacturer’s instructions on how many turns to wind the spring – over-winding could be very dangerous.

Repeat the process for the other spring.

9. Stretch and Set

You’ll now need to stretch each of the new springs one-quarter inch.

Place your winding bar flat and straight over the floor and insert it into the closest winding cone slot. Give it a knock with a hammer in the direction away from the center to loosen the spring.

Do this again for the other spring. Adjust the set screws on the rod for tightness, but be careful to not over-tighten and pierce the torsion rod. This is a good time to lubricate the new springs and the whole door with the lubricant recommended by the supplier.

You may now remove any clamps, reattach the garage door opener, and turn the power back on to test the door.


Now that you know how to replace garage door torsion springs, it’s up to you to decide whether this project is for you or if it’s better to call in a professional.

The mechanisms involved are relatively simple, but the springs and cables are under a great deal of pressure and can cause severe injury. If you are confident about your safety procedures and equipment, it can be worth your time to source the necessary springs for your garage door. Or, if you’re just not sure, an excellent option is to allow a garage door repair company to take care of all the details for you quickly and efficiently.

As always, if you believe this project is a bit beyond your experience level, we will be happy to help.

We’ve been a trusted garage door service provider serving Ventura and Los Angeles Counties since 1998! Discover why our customers love us and give us a call.

Garage Door Repair

How to Open A Garage Door With A Broken Spring

If you recently discovered your garage door won’t open and you suspect the problem may be because of a broken spring, you need to know how to open a garage door with a broken spring safely.

Garage doors are heavy and involve heavy machinery that can cause personal injury if you’re not careful.

Attempting to open a garage door with a broken spring can be dangerous for even the most experienced DIY homeowner, so we always recommend contacting a garage door repair service near you before anything else.

If you must open your garage door, you’ve come to the right place.

In this article we’re taking a closer look and providing a step-by-step overview of how to open a garage door with a broken spring safely.

How to Open a Garage Door with a Broken Spring

Your garage door is a crucial element in the safety and protection of your home. It keeps the belongings in your garage safe, and serves as an additional shield from the outside world; it can also bring visually pleasing elements to the front of your home.

If you have a broken garage door spring, we recommend you contact a reputable garage door repair company in your area. There is perhaps nothing more frustrating or stressful than needing to get your car out of the garage to hurry to school or work, but not being able to because a broken spring has rendered the entire door system inert.

This is a very common problem, and the door can be opened if the homeowner follows a simple process with safety precautions foremost in their minds. Understanding what causes this problem can also help prevent it.

What is a garage door spring?

A garage door spring has the ever-important job of supporting the door’s weight so it can be moved either manually or by way of a remote-controlled operating system. When this is not working, the full weight of the door will be very difficult and even dangerous to try to move. There are two main types of springs, and these include torsion and extension springs. The main difference between these two is the location of the spring itself.

A torsion spring is located above the door (while it’s shut), or on the inside front wall of your garage. They open and close along with the door, helping to support its weight. Extension springs, however, are most often located along the tracks of the garage door on both sides. The role of the springs in both cases is the same; the weight is just dispersed differently between the two.

Why do garage door springs break?

Think of how often you open and close your garage door. You likely open and close it at least a few times throughout the day, and perhaps even more if there are numerous people in your homecoming and going at different times throughout the day. When you add that up over a significant period of time, it is not surprising that garage doors take quite a beating and eventually the springs simply become tired and worn out.

Another contributing factor can come from the elements or a lack of maintenance–rust. Since the springs are metal, they can easily rust if not lubricated often enough. Rust makes the metal brittle and stiff, which will make it easier for the spring to break or snap apart in places. Regular maintenance involves applying a substance like WD-40 to the springs and testing them to listen for any squeaks in the spring that would indicate that the spring needs to be lubricated.

Opening Garage Door with Broken Spring

If you realize that your garage door spring has broken–whether it’s a torsion or extension spring–you’ll probably need a quick and safe way to open it so you can go about your day until you’re able to call a technician to fix it completely. Doing so is possible provided you can take the time to open it safely, and if you can have a relatively strong adult, a neighbor perhaps, helps you get the door open. Consider the following steps the next time you find yourself in this predicament:

  • You’ll need to put two six-foot ladders on either side of the front of the garage. These will help keep the door open once you’ve propped the door open completely.
  • You’ll also need two pry bars–one for you and one for your neighbor/helper. Each of you should insert these on opposite ends of the door at the same time, prying it up enough to grab onto the bottom edge with your hands.
  • Push it up at the same time, and slowly, taking care to not overextend your back or stand underneath the door while it isn’t secured, as this could cause serious injury.
  • Use vice grips attached to the track just below the door once you have pushed the door to the fully open position.
  • Then you can move the ladders into position, using them to rest the door on (after removing the vice grips). You can certainly leave the vice grips in place as an extra precaution against the door slipping out of place.

Even though this is a quick and sure-fire temporary fix that will help you get out of your garage and hopefully to work on time, you will certainly want to call a technician to replace the spring and inspect your garage door thoroughly as soon as you can. A technician is trained in all aspects of garage door care and maintenance and will be able to not only install a new spring but also help you anticipate and prevent breakages and malfunctions in the future.


Now that you know how to open a garage door with a broken spring, you can proceed safely.

Garage doors are an important part of your home, and they also are required to work hard on a daily basis. Making sure all parts of the door, including the springs–whether they are extension or torsion springs–will ensure that you’re not caught outside your garage and unable to get in, or worse, stuck inside your garage needing to get out.

Should you find yourself needing to open a broken garage door, the process is quite simple and just requires a few tools like vice grips, ladders, and an assistant. Safety is very important to keep in mind when following these steps, as garage doors can be quite heavy and opening a broken one improperly could result in injury.

However, it is important to note that once you open a broken garage door, you should contact a professional offering garage door services in your area. An experienced professional will help show you how to perform a garage door inspection and let you know what type of garage door maintenance is needed in order to avoid problems in the future. Doing so will ensure that you have a safe and functioning garage door that won’t cause inconveniences in the long run.

If you need assistance, please consider making Your Garage Door Guys your source for dependable garage door repair.

Exit mobile version